With hard water, mineral buildup will progressively develop on the inside walls of your water heater, preventing it from working correctly. As calcium and lime minerals build up in your water heater, the pipes clog, and the heater’s effectiveness decreases, causing your monthly bill to rise. That’s why it’s important to learn how to clean hot water heater with vinegar.
Flushing your hot water tank is the best approach to get rid of most of your problems, but if that isn’t enough, you can add vinegar to your hot water tank to help break up the deposits more and allow them to flow more readily.
This article will discuss the best method to clean your hot water tank and avoid paying massive bills!
When Should You Flush Your Hot Water Heater?
Regularly flushing your hot water tank is always a good idea, but it’s also helpful to know the signs of when it’s time for a flush.
You Are Not Able to Get Hot Water
If you can’t obtain hot water from your heater, sediment has probably built up to the point where it’s either blocking the element from lighting or stopping the heat from reaching your hot water valve.
Strange Noises from Your Water Heater
Sediment can form clusters and create calcified stones that end up smashing against the walls of your water heater in areas where the water is extremely hard. This indicates that you should flush the heater before the stones grow large enough to block the pipe.
Your Water Has a Strange Smell
While sediment accumulation is the most common reason for cleaning your hot water tank, germs can also form within a tank that hasn’t been cleaned in a long time. This bacterium presence can give your hot water tank a strange smell. You definitely need to clean the tank and flush it if this happens.
How to Clean Hot Water Tank With Vinegar
To clean a hot water tank with vinegar, you need the following items.
- Bucket
- Socket wrench
- 1-4 gallons of vinegar
- Towel
- Funnel
- Hose
Read on to learn about the steps for cleaning your water heater.
Removal of Anode
Turn Off the Power Supply
Before you do anything, turn off the power supply. You can do this from your home’s circuit breaker, which controls the tank’s power supply.
Turn On the Water Pumps
Open the tap to drain the water from the water tank. This helps prevent the formation of a vacuum inside the system. Turn the hot water faucet to the lowest setting to save water. It should be at a level that allows all of the water to flow through the tank. Make sure to turn on the faucet for the coming stages.
Connect the Pipe and the Drain Valve
Connect a hose to the tank’s hot water valve and store it outside the house or inside a bucket.
Turn Off the Cold Water Supply
Make sure to position the cold water supply pipe on the top of the water tank. Take a lever and attempt to deactivate it.
Drain the Water from the Hot Water Tank
It’s now time to remove the water from the hot water tank. Turn on the lowest drain valve and let it drain at least several gallons of water. When draining the hot water tank, always turn off the drain valve. You may turn off your home’s faucet after draining the volume of water.
Find the Water Heater Anode Rods
The anode rod is a corrosive metal that helps to prevent the tank from rusting. You can find it on the top of the tank. In certain situations, it’s affixed to the tank’s lid. If this is the case, you’ll need to use a screwdriver to remove the cover and gain access to the rod. The bolt is on the top of the tank, which should have a hexagonal shape.
Remove the Anode
It’s time to remove the anode rod from the water tank once you’ve found it. Loosen the screws with a wrench. Keep going until you can easily remove the rod.
Cleaning the Hot Water Heater Using Vinegar
Fill the Tank With a Vinegar Solution Using a Funnel
By now you should see a hole where the anode rod used to be. This is where you should put the funnel. Pour no more than four gallons of vinegar solution into the tank using this funnel.
Activate the Cold Water Supply and Replace the Anode Rod
The tank will refill with fresh water once you reinstall the anode rod and turn on the cold water supply. Allow the vinegar-infused water to remain in the tank for 24 hours. During this period, the acidity of the vinegar will destroy any sediment.
It’s now time to empty and clean the water tank. Turn on the water faucet and open the water supply valves at the bottom of the tank. Ensure that you connect the garden hose to the drain valve and keep the opposite end within the bucket.
Read More: Water Heater Temperature: What’s Ideal?
Why Is It Important to Clean a Water Heater?
The mineral deposits in the water can cause your water heater to become inefficient over time. This problem arises as the water heater fills with mineral buildup, which becomes resistant to the interior walls, causing your water heater to malfunction.
When lime and calcium are mixed in a water heater, it considerably reduces the heating efficiency of the heater. Uneven heating, a failing element, and a clogged drain valve are all examples of inefficiencies.
Sediment accumulation can also cause leaks in your water heater tank in some situations. Proper maintenance is necessary in order to maintain a functioning and energy-efficient water heater. The easiest method to avoid this is to flush the system regularly.
Endnote
Cleaning your hot water heater with vinegar alone will not solve the problem. A few other products, such as a water softener, can assist you in keeping your water heater in good operating order.
Keep in mind that regular maintenance of your heater can help you get the most use out of it. If you’re unsure about cleaning your water heater, don’t panic! There are always specialists who are ready to help you with whatever you need.
Related Articles:
Self Cleaning Water Heaters: Are They Worth the Money?